AISI S213-07-S1-09 PDF

AISI S/S (). DISCLAIMER The material contained herein has been developed by the American Iron and Steel Institute Committee on Framing. AISI S / S () North American standard for cold-formed steel framing – Lateral design,. edition reaffirmed Not for loan. AISI S North American Standard for Cold-Formed Steel Design, Edition (Reaffirmed ); AISI S w/ S (): North.

Author: Shara Nikosar
Country: Tunisia
Language: English (Spanish)
Genre: Education
Published (Last): 2 April 2012
Pages: 153
PDF File Size: 16.54 Mb
ePub File Size: 1.30 Mb
ISBN: 563-1-91594-404-7
Downloads: 66085
Price: Free* [*Free Regsitration Required]
Uploader: Faukora

RdRo is taken equal to or less than 2 for sheathed shear walls, and equal to or less than 1.

Free CFS Publications from the AISI/SMDI Construction Market Council

If the load combinations for Allowable Stress Design ASD with the system overstrength factor are desired to be used and they are to be checked against the member nominal strength, then member s213-07-ss1-09 strength is required to be divided by 1. Shear values are permitted for use in seismic design where the seismic response modification factor, R, is taken equal to or less than 3, subject to the limitations in Section C1.

The probable capacity is only used to estimate the forces in the design of the non-fuse elements of the SFRS. In the case of a coldformed steel framed shear wall, the Xisi elements include the chord studs, intermediate studs, hold-down anchors, track, etc.

If either Ry or Rt is determined by test, then both Ry and Rt must be a test value. Capacity based design approach is s213-07-d1-09, assuming the sheathing connections act as the energy-dissipating element See Section C5. Foundations shall be designed ais resist the loads resulting from the lesser of the loads that the system can deliver C5. The strap braces were expected to undergo s213-07-z1-09 cross-section yielding along their length, while the s213-07-s1-9 elements in the seismic force resisting system SFRS were selected to be able to carry the probable brace capacity.

  JOSE LUIS MERLIN EVOCACION PDF

This can be achieved by applying an overstrength factor to the nominal resistance Figure C Note that the lower RdRo value of 1.

For wood structural panel sheathed shear walls, tabulated Rn values applicable for short-term load duration seismic loads. Serrette conducted tests on cold-formed steel frame shear walls utilizing structural adhesives.

Indeed, in many jurisdictions, such review is required by law. Lateral system not specifically detailed ausi ductile seismic performance Capacity based design approach not required. When R is less than or equal to 3, Section D3 is not required. Medias this blog was made to help people to easily download or read PDF files.

If a Capacity Based Design approach is not implemented, then the ductility of the wall may be reduced due asi failure of one or a number of other elements in the SFRS. For Seismic Z213-07-s1-09 Category A through C, the designer has the option to use an R of 3 for systems with a higher assigned R to determine the seismic load and thereby avoid the special detailing in Section C5.

The design of diaphragms that resist wind, seismic or other in-plane lateral loads shall comply with the requirements of this section.

The connection of the diagonal strap bracing member shall be welded and designed to permit gross cross section yielding of the diagonal strap bracing member, unless one of the following criteria is satisfied for the aidi connection: The design of cold-formed steel members to support the additional mass of concrete and masonry elements needs to be in accordance with AISI S [CSA S] and required deflection limits as specified in concrete or masonry standards s213–07-s1-09 the model building codes.

Structural panels shall be permitted to be applied either parallel to or perpendicular to framing. The Committee has made a diligent effort to present accurate, reliable, and useful information on cold-formed s framing design and installation. Fiberboard panels shall comply with AHA A Upanishad Commentary Full Eng commentary on the vedanta and upanishads to get a insight to profound knowledge of vedic seers.

  INTELECT MOBILE LASER PDF

Free CFS Publications from the AISI/SMDI Construction Market Council –

The eccentric effect due to single sided bracing is neglected for purposes of this classification, but shall be considered in sisi with C5. For intermediate values of opening height ratio and percentages of full-height sheathing, the s213-07-s1-099 resistance adjustment iasi shall be permitted to be determined by interpolation.

An individual sample may include several thicknesses for a s2113-07-s1-09 sample grade and coating. Unless otherwise noted, all sheathing edges shall be attached to framing members or blocking. The Rd value was reduced for the situation where gypsum sheathing is relied upon in seismic design to account for the decreased ductility of the system, similar to the NBCC listing for wood framed walls with gypsum panels.

Hikita verified that shear walls subjected to combined gravity and lateral loads can perform at an adequate level to warrant the use of the tabulated Rd and Ro values, if the chord studs are designed to carry the anticipated compression force, related to sheathing connection failure during a seismic event, combined with the associated NBCC principal and companion gravity loads.

Asclepius, Commentary on Nicomachus. Unblocked assemblies shall be permitted provided the nominal resistance values above s231-07-s1-09 multiplied by 0. Standard Language and Poetic Language Analysis of ss between standard language and poetic language.

The nominal strength [nominal resistance] so calculated defines the maximum resistance that the diaphragm, shear wall, or diagonal strap bracing is capable of developing. Alternatively, for diaphragms sheathed with wood structural panels, the available strength may be determined by the section D2.

Back to top