ASTM E547 PDF

based on specific design pressures (DP). ▫ Water penetration resistance (ASTM E and ASTM E). ▫ Uniform load deflection test (ASTM. ASTM International E Standard Test Method for Water Penetration of Exterior Windows, Skylights, Doors, and Curtain Wall by Cyclic Static Air Pressure. ASTM E Standard test method for water penetration of exterior windows, skylights, doors, and curtain walls by cyclic static air pressure difference.

Author: Daile Shasar
Country: Martinique
Language: English (Spanish)
Genre: Environment
Published (Last): 19 July 2012
Pages: 115
PDF File Size: 13.39 Mb
ePub File Size: 11.67 Mb
ISBN: 128-1-88295-769-9
Downloads: 73506
Price: Free* [*Free Regsitration Required]
Uploader: Fauktilar

In no case shall there be less than two test cycles, and no cycle shall be less than 5 minutes in duration. These factors should be fully considered prior to specifying the test pressure difference to be used. Give us a call today for more information or to discuss you next project. MISSION Professional services based e457 accurate information that helps you or your company make the right decision asrm your project or asset.

The values given in parentheses are mathematical conversions to inch-pound units that are provided for information only and are not considered standard. In service, the performance will also depend on the rigidity of supporting construction and on the resistance of components to sstm by various causes, vibration, thermal expansion and contraction, etc.

In my last blog, I focused on a long standing and very useful laboratory test used to measure water penetration: Professional services based on accurate information that helps you or your company make the right decision regarding your project or asset. For a negative pressure system, the water-spray grid would be located outside the chamber and the air supply would be replaced by an air-exhaust system.

In service, the performance will also adtm on the rigidity of supporting construction and on the resistance of components to deterioration by various causes, vibration, thermal expansion and contraction, etc.

Failures during quality assurance new construction testing can result in unnecessary delays that impact your bottom line. We provide testing services throughout the United States from our headquarters satm in Atlanta, GA. BDG has extensive knowledge of most aatm systems and specializes in forensic water intrusion investigations.

It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory astmm prior to use. In recent earlier blogs I reviewed the primary wall types and how each created different challenges for adhesives and sealants in preventing water ingress into the wall assembly.

See the summary for E in this link: To watch a three minute video for an AAMA The values given in parentheses are mathematical conversions to inch-pound units that are provided for information only and are not considered standard.

  HRF3205 DATASHEET PDF

However, unlike E the E test attempts to simulate more real life exposure by cycling the pressure across the test specimen as the test procedure progresses.

ASTM E | Water Penetration Testing

The ASTM E testing is performed by applying water to the exterior of the test specimen while lowering the pressure inside by means of an air chamber built on the inside or opposite side of the test specimen. This test method does e54 address these issues. The most essential steps in running the E test, once the wall assembly is attached and sealed to the ASTM E test wall, are listed below. For specific hazard r547, see 7.

The list below shows what we have discussed so far and the next steps. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided astj part of the standard. The ASTM E Standard Test Method for Water Penetration of Exterior Windows, Skylights, Doors, and Curtain Walls by Cyclic Static Air Pressure Difference is a testing standard of procedures used to determine the water penetration resistance of windows, curtain walls, skylights, and doors when water is applied xstm a calibrated spray apparatus while simultaneously applying cyclic static pressure to opposite sides of the test specimen.

Historical Version s – view previous versions of standard. Link to Active This link will always route to the current Active version of the standard.

These methods are often used both for determining the cause of existing building air leakage and for confirming the adequacy of newly constructed wall designs. Some designs are more sensitive than others to this upward moving water. If you are looking for a reputable second or third-party testing company to perform accurate professional testing, provide concise reports, and help you through the entire process, contact BDG today.

Water that penetrates the assembly, but does not result in a failure as defined herein, may have adverse effects on the performance of contained materials such as sealants and insulating or laminated glass.

This test method does not address these issues. The air-pressure differences acting across a building envelope vary greatly. Blog Building Wall Assemblies: It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. See the illustration below. The air-pressure differences acting across a building envelope vary greatly. BDG utilizes professional testing equipment that is calibrated to each specific testing standard for accurate results.

  ANNA KOMNENE PDF

In applying the results of tests by this test method, note that the performance of a wall or its components, or both, may be a function of proper installation and adjustment. The water spray system has nozzles spaced on a grid to deliver water so that the test specimen is wet uniformly, including those areas vulnerable to water penetration. It is difficult to simulate the identical complex wetting conditions that can be encountered in service, aatm large wind-blown atsm drops, increasing water drop impact pressures with increasing wind aastm, and lateral or upward moving air and water.

The E test, like E, provides the details of the instrumentation similar to ASTM E to create a pressure difference across a multitude of building assemblies during the calibrated water spray minimum aetm of 3. Water that penetrates the assembly, but does not result in a failure as defined herein, may have adverse effects on the performance of contained materials such as sealants and insulating or laminated glass.

In applying the results of tests by this test method, note that the performance of a wall or its components, or both, may be a function of proper installation and adjustment. This test method does not identify unobservable liquid water which may penetrate into the test specimen. These factors should be fully considered prior to specifying the test pressure difference to be used. The testing pressure differential is usually determined by the testing specifier. We also looked at how sealants and adhesives provide air leakage resistance and how the air leakage is related to water ingress as well.

Our field asgm are properly trained and knowledgeable of all testing satm. This allows us to not only properly test fenestrations on new construction projects, but also pinpoint the cause of any test failures and provide accurate recommendations to achieve successful testing results. I also detailed the value of assembly e54 which evaluates the complex details in real building walls versus material testing that evaluates a specific property without linkage to the wall geometry and the different substrate conditions in the wall.

ASTM E547 – 00(2016)

It is difficult to simulate the identical complex wetting conditions that can be encountered in service, with large wind-blown water drops, increasing water drop impact pressures with increasing wind velocity, and astmm or upward moving air and water.

This test method does not identify unobservable liquid water which may penetrate into the test specimen. Building Diagnostics Group, Inc.

Back to top