Digitech RP80 Pdf User Manuals. View online or download Digitech RP80 User Manual. User guide • Read online or download PDF • DigiTech RP80 User Manual • DigiTech Musical Instruments. User manual for the device DigiTech RP Online user manual database.
|Published (Last):||14 June 2006|
|PDF File Size:||4.97 Mb|
|ePub File Size:||14.50 Mb|
|Price:||Free* [*Free Regsitration Required]|
WarrantyWe at DigiTech are very proud of our products and back-up each one we sell with the following warranty: The warranty registration card must be mailed within ten days after purchase date to validate this warranty.
Digitech warrants this product, when used solely within the U.
You now have the flexibility and power toproduce sonic creations never before thought possible. It is your key to unlocking the potential within the RP The Up Footswitch increments, and the Down Footswitch decrementsthrough the presets. Pressing both Footswitches simultaneously bypasses theselected preset. Pressing and holding both Footswitches accesses the Tuner.
Display – The Display provides information for digjtech functions depending on the selectedmode. In Play mode, the display shows the selected preset number. In Edit mode,the display shows the value of the parameter being adjusted. When the Tuner isenabled, the display shows the note played.
Store – The Store button saves your custom edits to the user presets. Input – Connect your instrument to this jack.
Use the Left Output for all monoapplications. See Page 23 formore on Global Cabinet Modeling. Making ConnectionsThere are several different connection options available when using the RP The followingdiagrams show the connections for some of these options. Before connecting the RP80, make sure that the power to your amplifier is manusl off, and thepower to the RP80 is disconnected.
DIGITECH RP80 Manuals
There is not a power switch on the RP If connecting to a mixing console, set the pan controls of themixer hard left and right to retain stereo separation. Applying PowerThere are two options for powering the RP Before applying power to anything, set your amp s to a clean tone and set thetone controls to a flat EQ response on most amps, this would be 0 or 5 on the tone controls.
The battery compartmentis located on the bottom of the RP The following diagram shows how to install thebatteries. Connecting a cable to the Input applies power to the RP Disconnecting your instrumentfrom the Input of the RP80 disconnects the battery power. Turn your amplifier s on andadjust the volume s to a normal playing level. TunerThe Tuner in the RP80 lets you quickly tune or check the tuning of your guitar. Enter theTuner by pressing and holding both Footswitches simultaneously.
The tu briefly displaysindicating that you are in Tuner mode. To begin tuning, play a note on your guitar the neckpickup usually works best. The display shows the note being played. The Effect LEDsindicate whether the note is sharp or flat.
The right 6 red LEDs indicate the note is sharpand should be tuned down.
The Edit buttons move you through the Effect modules. The LEDs light indicating which effectgroup is selected. Each effect has multiple settings to select from. The Value buttons are used tochange the value for the selected effect. As a button is pressed, the value or manuao is shown inthe display. The following steps outline how to store changes to a preset or copy apreset to a different location: Use the footswitches toselect the preset location youwant to store your changes to.
Each effect within the RP80 can be programmed to suit your personal application. Understanding how these effects alter the sound helps you achieve the sound you are lookingfor.
SH – Gives a single coil pick up the warm tone of a humbucker. HS – Gives a humbucker the unique sound of a single coil.
What’s missing? Tell us about it.
Cr – Cry Wah is a traditional sounding Wah. Fr – Full Range Wah sweeps the entire spectrum of audible frequencies. EQEqualization is used to shape the tonal response of your guitar signal. The EQ in the RP80is similar to the tone knobs on an amplifier.
DIGITECH RP80 USER MANUAL Pdf Download.
Values cut the level of each band, 5 is flat no cut or boostand values boost the level of each band. Bass b1- b9 – The Mxnual buttons adjust the amount of low end enhancement Bass. Mid d1- d9 – The Value buttons adjust the amount of mid range enhancement.
Treble t1- t9 – The Value buttons adjust the amount of high end enhancement Treble. Chorus C1-C9 A Chorus adds a short delay to your signal. The delayed signal is modulated in and outof tune and then mixed digjtech with the original signal to create a thicker sound, andstereo image. Ro80 the Value buttons to select one of the diitech Chorus settings.
Flange F1-f9 A Flanger uses the same principle as a Chorus but uses a shorter delay time and addsregeneration or repeats to the modulating delay.
This results in an exaggerated upand down sweeping motion to the effect. Vibrato b1-b9 A Vibrato effect modulates the pitch of the incoming signal at an even rate. Use theValue buttons to select one of the nine Vibrato settings. Rotary Speaker r1-r9 Rotary Speaker is an emulation of a device that included a spinning horn and woofer. The rotation of these two speakers produces an interesting combination of soundpanning from pr80 to side with a slight pitch change produced from the speed of thesound coming towards, and then going away from the listener.
Detune d1-d9 A Detuner makes a copy of your incoming signal, takes the copied signal slightly out oftune from the original, and mixes the two signals together.
DigiTech RP80 user manual – – Solve your problem
The result is a doubling typeof effect as if two guitars were playing the same part together. Use the Value buttonsto select one of the nine Detuner settings. There are two different parameters used to program thedelay, Delay Variation and Time. The second delay parameter is Delay Time. This is indicatedby a value 10msms1.
When a parameterhas been assigned to the Expression Pedal, a programmable minimum and maximum valuecan also be assigned.
The procedure for assigning a parameter to the Expression Pedal is asfollows: Drum MachineThe RP80 includes several sampled drum patterns that are useful for developing a goodsense of timing. Press the Drums button againto stop playback of the drum loop.
This procedure erases allcustom user presets. Performing this function erases all user-programmed data. All such data will be lost forever! The procedure for performing a Factory Reset is as follows: This calibration procedure is automatically entered after a factory resetprocedure. This will not erasethe User Presets.
The procedure for Calibrating the Expression Pedal is as follows: Page 4 WarrantyWe at DigiTech are very proud of our products and mxnual each one we sell with the manuzl warranty: Page 6 The Front Panel Page 7 1.
Page 9 Rear Panel Page 10 Making Mwnual are several different connection options available when diigitech the RP Page 13 Connecting a cable to the Input applies power to the RP Page 20 EQEqualization is used to shape the tonal response of your guitar signal.
Page 22 Vibrato b1-b9 A Vibrato effect modulates the pitch of the incoming signal at an even rate. Page 23 Detune d1-d9 A Detuner makes msnual copy of your incoming signal, takes the copied signal slightly out oftune from the original, and mixes the two signals together.
Page 27 Drum MachineThe RP80 includes several sampled drum patterns that are useful for developing a goodsense of timing. Don’t see a manual you are looking for? Tell us what’s missing. Tell us about it. Or point us to the URL where the manual is located.
Your manual failed to upload