View and Download Dynalink RTAW user manual online. ADSL2+ Wireless Modem Router. RTAW Wireless Router pdf manual download. or DNS settings manually encoded on your network card. PPPoE Dynalink RTA W By default the RTAW does not have wireless security setup. PPPoE connection does not require you to have an IP address or DNS settings manually encoded on your network card. PPPoE connection uses authentication .

Author: Nisida Vosho
Country: Albania
Language: English (Spanish)
Genre: Music
Published (Last): 8 March 2014
Pages: 346
PDF File Size: 20.15 Mb
ePub File Size: 16.56 Mb
ISBN: 146-5-18264-176-9
Downloads: 15027
Price: Free* [*Free Regsitration Required]
Uploader: Tosida


It can provide stronger encryption and authentication solution than other WPA mode. When prompted with Network Settings Change dialog box, click Yes to restart your computer. To delete the setting, click another IP filtering, click Add again.

This web page offers eight authentication protocols for you to secure your data while connecting to networks. Select User Certificate, then Next.

Dynalink RTAW | Actrix

Manuaal can choose where to store the logs; the options include Local, Remote and Both. Page 24 Chapter 2: ADSL Router User Manual Repeater A repeater is an electronic device that receives a weak or low-level signal and retransmits it at a higher level or higher power, so that the signal can cover longer distances without degradation.

Click this button to refresh the current time.

The main screen will be shown as below. Default factory settings for Dynalink RTAW If you have performed a reset of your RTAW device or not changed the defaults, you should be able to access it with the following settings: Page Quality of Service QoS Quality of Service is an industry-wide initiative to provide preferential treatment to certain subsets of data, enabling that data to traverse the Internet or intranet with higher quality transmission service.


If you want to squeeze a little bit of extra functionality out of your router, consider flashing an open-source firmware like dd-wrt, openWRT or LEDE.

System Requirement And Installation Chapter 2: System Requirement and Installation On the General tab, check out the list of installed network components. It decides the speed of data transmission. Hard reset instructions for Dynalink RTAW If your RTAW router is not working as it should, dropping connections or not being responsive, you should first do a reset of the router to see if the problems persist.

Update Firmware If you have to or want to update the firmware for this router, you can open the Update Firmware web page and choose the correct file by pressing Browse. Press Close to start using the router.

Refer to the relevant operating system to install the USB drivers. Basic Settings To set the basic configuration for the wireless features, please open Rta102w page from the Wireless menu.

Please follow the steps below to set your network adapter. Check the Validate server certificate check box if server certificate validation is required Select Browse my computer for driver software advanced. Be sure to reboot your router for these changes to take effect. After pressing Next, you will see the web page listed as the right one. When users are executing firmware upgrade and saving settings to the router, the power for the router is lost for some unknown reasons, the normal web page for the router might be damaged.

Connecting the ADSL line. Select the support of line modes: Page 44 Chapter 2: Once rebooted click on the Wireless tab dgnalink the top and make sure the settings are as follows, then click Apply. Click Network and Internet.

  FEM 9831 PDF

For Installation Use only dynalihk type of power source indicated on the marking labels. Open the Start menu, and type cmd in the text box then click OK. To access the Internet, private network should have an agent to translate the private IP address to public IP address. Backup Config Chapter 4: A dialog appears to ask you to choose the program that you want janual remove. System Log Chapter 4: For Windows NT 1.

Dynalink RTA1025W User Manual

Open the Start menu, and click Run Port Mapping Chapter 4: If the previous one is failed, than the items following that one will be failed, too. Show me other options. If you do not know much about the router, you can use the Quick Start pages to adjust basic settings to activate your router.

Select this item to make the connection active all the time. Accessing The Internet Chapter 3: Make sure the contents match the settings provided by your ISP. If you have already changed the password use that instead.

Overview This chapter provides you the description for the LEDs and connectors on the front and rear surface of the router. Page 22 Chapter 2: If everything is OK, click Finish to accept these settings. The router will assign IP address and gateway address for each of your PCs.

Page 58 Chapter 2: When returning to the Network window.

Back to top