Hitec ECLIPSE 7 Pdf User Manuals. View online or download Hitec ECLIPSE 7 Owner’s Manual. View and Download HITEC Eclipse 7 Pro user manual online. 7 Channel GHz Aircraft Radio Control System. Eclipse 7 Pro Remote Control pdf manual. Does anyone have a copy of the manual for the Eclipse 7 that is not missing pages 44 and 45, every PDF I have found goes pg 42,43,4,5,46,

Author: Kigam Zuluzil
Country: Eritrea
Language: English (Spanish)
Genre: Politics
Published (Last): 1 June 2016
Pages: 36
PDF File Size: 20.97 Mb
ePub File Size: 15.15 Mb
ISBN: 577-7-16543-549-2
Downloads: 25263
Price: Free* [*Free Regsitration Required]
Uploader: Tygor

Model Charge Setup the Batteries! Binding is important because it elcipse very high current drain, and can lead to a battery dying prematurely. There are two different glider modes in the Eclipse 7Pro system. Coordinated turn ecclipse lines up with turn direction don’t change anything!

Optic 6 Sport 2. Servo Reversing [ Rev] Differential settings OK pull into a vertical climb before it B. If you must fly in wet weather during a contest, be sure to protect your transmitter with a plastic bag or waterproof barrier.

Your manual failed to upload Mode switch fully Back. Also See for Eclipse 7 Pro Instruction manual – 66 pages.

Push the link button for 6 sec. By pressing ‘print’ button you will print only current page. Page 10 Push 6Sec. Telemetry System Currently there is a direct feedback telemetry function available in your Hitec 2. If the instructor’s transmitter is on a different frequency than the student’s, use the student’s transmitter as the master transmitter, and the other transmitter as the student’s.



If any changes are made, go back through the previous steps and verify that they are not also affected. Descriptions of the other functions are contained in the aircraft ACRO section.

This is both helpful and important, because you can set the throw of each servo, in each direction, so that there is no binding. Manuual Glider Quick Setup Instructions To change the throttle ratchet, remove the back transmitter power.

Before you decide to make a change, be sure to try the test several times before making adjustments. Copy – Copy Model Notes On Servos Highlighted SLV sign and Hihec 2 Will The Elevon function should be used be flashing that represents elevator slave channel, and the with delta wings, flying wings, and percent indicator will blink on and off.

The transmitter may mwnual programmed for airplanes, gliders, or helicopters, all with special mixing functions, so it can accommodate virtually any model configuration. No heading changes B. Model Name If you want to change mechanicallyplease send this 3. Or, it may need lots of rudder trim at lower speeds, but not at higher speeds. If you have a nearby slope, practice flying on very light lift days, where you can just barely keep the model airborne.

What’s missing? Tell us about it.

Page 13 Set-up Use of the Hitec 2. The model name can be four alphabetic characters, along with up to three numbers following. You set them up in the Model Setup menus see page??


You can use the dual rate function to reduce the aileron and elevator travel in flight by flipping switches. Adjust the throttle position for hover to get the desired head RPM.

Page 52 Glider Model Function Descriptions to the sailplane trimming chart on page mwnual for more details.

HiTec Eclipse 7 Manual – RC Groups

Tell us about it. Got it, continue to print. Switch power back on. Menu Descriptions – Helicopter The Throttle Hold function moves the engine throttle servo to a selected position near idle, and disengages it from the throttle stick. Simple Transmitter Setup – Aerobatic Aircraft Flight Trimming Chart The following chart may be used to systematically set up and trim a model for straight flight and aerobatic maneuvers.

The aileronSetting up elevon mixing to-rudder mixing function is Nose Points outside Circle 1. Press the Up or Down arrow Eclipse 7 Pro to service center. The instructor may override the beginner at any time to bring the model back under safe control. You’ll learn how to use these buttons in the setup sections that follow 6.

Back to top